Man: Broken taillight? I didn't know about a broken taillight. 男士:尾灯碎了?你不说,我还真不知道尾灯碎了。
The officer had earlier stopped the suspect's car because of a broken taillight when Hood, jumped from his car and ran into the woods. 当时,里特看到胡德的车尾灯坏了,觉得有可疑,就截停胡德的汽车。接着,胡德从车里跳出来,跑进了森林。
The automatic switch has light function ( delay time for three minutes): The light is opened automatically while opening the door, shut off the door taillight to go out automatically. 动开关照明灯功能(延时三分钟):开门时灯自动打开,关闭门后灯自动熄灭。
The Tiida hatchback's taillight design and rear bumper shape have been refreshed, and new16-inch alloy wheels are available for both the hatchback and sedan. 其中掀背的尾灯和后保险杠也有了更新的设计,新的16寸合金轮胎作为两款车的备选配置。
Okay, I owe you a left taillight and a rear bumper. 好吧,我欠你个左尾灯和一个后保险杠。
Both the headlamp and the taillight are integrated. 无论是头灯和尾灯集成。
The rear of the truck sports new plastic taillight covers. 后面的卡车运动新整形尾灯覆盖。
Because your taillight is out, and we couldn't see you brake. 因为你的尾灯坏了所以我们看不到你停车。
For example, there's the taillight design composed of a pair of three vertical red bars. 举个例子,设计的尾灯是由一对三竖条红灯组成。
Technnological design and numerical simulation on forming process of taillight supporter of car; 汽车尾灯支架属汽车覆盖件,其结构尺寸大,形状复杂,成形过程难以确定。
Additionally, the bicycle features a static inner wheel system with safety features such as integrated reflectors on the rotating outer wheels and a taillight, which is mounted in the bike's frame. 此外,自行车功能静态内轮系统的安全功能,如集成的反光板的旋转外车轮和尾灯,这是安装在自行车的框架。
But rather than just replacing bulbs with LEDs, the designers attempted to'spread the light'through the design of the taillight unit and the use of reflective surfaces. 但是,而不是取代发光二极管灯泡,设计师试图'传播通过尾灯组的设计和反射面使用轻'。
You've got a rear taillight that's nonfunctional. 你有一个尾灯坏了。
I stopped you because your taillight is out. 我让你停车是因为你的尾灯坏了。
The rear has a discreetly decorated boot lid and carbon fiber taillight covers. 后方有一个谨慎的装饰启动盖子和碳纤维尾灯涵盖。
I didn't know about a broken taillight. 我不知道我有个尾灯是坏的。
Building the simulating model of car taillight and its general fuzzy evaluation 轿车尾灯计算机辅助仿真造型建模及其综合评价
This thesis find the basis paths and methods of automobile panel simulation and finite element model building by researches of taillight supporter and other auto panels; 本文通过对汽车尾灯支架及其它一些覆盖件的研究找出了覆盖件有限元模型建立及模拟的基本流程和方法;
At present die design, 3D die design is the trend of development. This thesis designed 3D die of blanking and draw processes of taillight supporter with UG software, Summarized the merits and the characteristics of 3D die design. 最后,在现代模具设计里,三维模具是发展趋势,本文结合UG软件对汽车尾灯支架落料和拉延工序的模具进行了三维设计,总结了三维模具设计的优点和特点。
The numerical simulation of drawing process for car's taillight pedestal is studied by using the three-dimensional sheet metal forming analysis and non-linear explicit algorithm software Dynaform. 采用基于动力显示算法的板料成形非线性有限元分析软件Dynaform对某轿车后灯座的拉深成形过程进行了数值模拟仿真。
Using PRO/ E& ANSYS software as platform, the simulating model of car s taillight has been built with the technology of computer aided molding and our simulating CAD/ CAM/ CAE system for automobile parts also has been set up. 利用计算机辅助造型技术,以PRO/E-ANSYS软件为平台,对轿车尾灯进行了仿真造型建模,从而建立了自己的汽车部件仿真CAD/CAE/CAM系统。