m/min
英
美
网络 速度; 线速度; 米/分钟; 最大速度; 最大线速度
双语例句
- The finite element simulation of stress and strain of 230 mm slab with casting rate 1.0 m/ min and 3 different roller ways layout-single-point, four-point and continuous straightening have been carried out by elastoplastic finite element method.
采用弹塑性有限元分析法，对拉速1.0m/min、厚度230mm的板坯，在3套不同的辊列布置的单点矫直、四点矫直、连续矫直进行应力应变的有限元模拟。 - It is obtained that maintaining liquid level stabilizing, nozzle immersing depth 400~ 600 mm and controlling casting speed~ 1.0 m/ min are favourable to optimize liquid steel pattern and promote inclusion floating off, and the rectangular tundish structure is better than circular tundish structure.
结果表明，保持中间包液面稳定，水口插入深度400～600mm，拉速～1.0m/min有利于优化钢水流场，促进夹杂物上浮；矩形中间包结构优于圆形中间包结构。 - The saturation compression speed was 1 m/ min, the stop time for each 10 m increment was 2 min, and that at 60 m was 20 min.
饱和加压速度1m／min，每10m增值停留2分钟，60m深度停留20分钟。 - The results show that the limit current density, the depositing rate and current efficiency increase remarkably, the depositing rate reaches to 47.33 μ m/ min, which is about 90 times as that of conventional deposition.
结果表明：采用该方法后允许使用的极限电流密度、沉积速率及电流效率均显著增大，沉积速率高达4733μm/min，是一般槽镀的90倍左右。 - This will be realized in the existing one-strand configuration, by improving the equipment performance and increasing the caster speed unto 8 m/ min with a 70 mm thick slab.
这将由现存的1流配置来实现，其措施包括改进装备性能和将70mm厚铸坯的拉速提高至8m/min。 - In order to help the large and high speed PM installation and alignment, the installation standard data of PM 800~ 1600 m/ min is introduced in this paper.
本文综合安装实践和国外资料，简要介绍了车速为800～1600m／min纸机的找正参数。 - Casting starting and before stopping, the drawing speed should be reduced below 2. 0 m/ min, otherwise, the initial pressure can not be great enough to compensate the loss of the path pressure of the horizontal shrinkage compensation.
启铸和停铸前阶段，需把拉坯速度下降到2.0m／min以下，否则钢液的初始压力不足以补偿水平补缩沿程压力损失。 - The results indicate that local flux is not consistent with average heat flux when the casting speed is 1.4~ 2.6 m/ min and EMS-current is 200~ 320 A.
结果表明：拉速为1.4~2.6m/min，搅拌电流在200~320A时，局部热流与平均热流变化趋势不完全一致。 - This paper introduces technological features of high oriented yarn ( HOY), whose speed exceeds 6 000 m/ min, and therefore has strict requirements for spinning equipment and process.
介绍超高速纺丝（HOY）的技术特点。HOY纺丝速度超过6000m/min，对纺丝设备、工艺流程有较高的要求。 - Even the relative low wire feed rate of 6 m/ min exceeds 3 times of routine TIG welding, which greatly improves the welding efficiency.
6~10m/min的送丝速度较常规TIG焊接提高了3倍以上，大大提高了焊接效率。 - It was concluded that the POY produced at the spinning speed range of 2 800-3 200 m/ min had the performance indexes suitable for post-processing.
分析得出纺丝速度在2800～3200m/min时制得的预取向丝具有适宜于后加工的性能指标。 - Field operation shows that running at a high speed of 90 m/ min, the system is able to detect the surface defects of wide film with the width of 1 300 mm in real time and operates normally.
现场运行结果表明，系统能够完成对运行速度为90m/min，宽幅为1300mm的胶片表面弊病的检测任务。 - The effect of non-sinusoidal oscillation amplitude on liquid friction force in mold with casting speed 2. 0 m/ min has been analyzed by a mathematical model of liquid friction combined a non-sinusoidal oscillation waveform with optimum mode virtue to get amplitude selection principle and determination method.
利用结晶器液体摩擦力模型，结合具有最佳振动模式特点的非正弦振动形式，分析了2.0m／min拉速时非正弦振动振幅对液体摩擦力的影响，给出了振幅选取原则和确定方法。 - When output speed is 600 m/ min, the control range of weight variation is ± 2%.
在600m／min出条速度下，重量偏差的控制范围可达±2%。 - 30 m/ min above the lactate threshold intensity.
30m/min为高于乳酸阈强度。